How do I light my RV furnace

2 Press Pilot Knob Go to your furnace access panel and remove its cover. Turn your gas dial to the pilot position and hold down the knob. 3 Light the Pilot If you have a striker ignition device, press it several times. You can also light the pilot burner with a lighter or match.

How do I light the pilot on my RV furnace?

How do I light the hydro flame on my RV furnace?

Charge your RV’s battery up and turn the Atwood Hydro-Flame furnace’s gas valve on to the “pilot” position.
Light a match while pushing and holding the gas valve. …
Allow the gas flame to burn for a moment before switching the gas valve over to the “on” position.

Why will my RV furnace not ignite?

If it’s an electric furnace, then possible reasons for ignition failure includes the battery power not being sufficient or the fuse in the furnace being blown. When a propane or gas furnace isn’t igniting, the problem can be that you don’t have enough propane supply or your gas valve is not opening.

How do you light a propane furnace?

Locate the valve control on the furnace. …
Check to make sure nothing is obstructing the pilot light assembly. …
Turn the valve to the “Pilot” position on the settings. …
Light a match, and hold the flame to the pilot light opening.

Where is the pilot light on my furnace?

Near the bottom of your furnace is a switch that normally says “Pilot,” “On” and “Off.” Find this switch and turn it to the “Off” position. Wait at least five minutes. This is important because it gives the gas time to dissipate, which is necessary to avoid possibly starting a fire.

Is there a reset button on an RV furnace?

All furnaces are equipped with a reset button. They are generally red or yellow and are located inside the blower compartment. The reset button is a safety feature that will shut down the furnace when a problem is detected, often a hot or overheating furnace, before it trips the circuit breaker.

How do you test an RV furnace ignitor?

Make Sure The Furnace As At Room Temperature. …
Turn Off The Furnace. …
Switch Off Circuit Breaker. …
Remove Furnace Service Panel. …
Look For Visible Damage. …
Remove Ignitor Wires From Socket. …
Test The Ignitor With A Multimeter.

How do you reset a furnace on a camper?

Resets and Lockouts The lockout condition can be reset by turning the thermostat off and reducing the temperature to a value which would not cause the furnace to turn on. Wait approximately 30 seconds and then turn the thermostat back on and increase the temperature to the desired level.

Where is the flame sensor on an RV furnace?

A furnace flame sensor is a very basic part of your furnace. It’s located on the burner assembly and is just a thin metallic rod. It’s usually bent, and it sits just in front of the pilot flame inside the furnace.

Article first time published on

What is Hydro Flame Furnace?

The Hydro Flame RV Furnace is one of the first units you’ll encounter in your search. This is a lightweight, compact model, weighing in at just 23 pounds with dimensions of 11-3/8″ high, 8-3/8″ wide, and 20-1/2″ deep.

What is Hydro Flame?

HydroFlame offers a technology solution to benefit businesses involved in Heavy Oil and Bitumen production. HydroFlame Technologies, LLC was established in August 2008 with the sole purpose of commercializing the HydroFlame novel direct contact…

How does an RV propane furnace work?

When you set the thermostat higher than the RV’s temperature, the blower motor gets activated. Gradually, the heater begins to warm your RV, as propane burns to create hot air, and the ducts in the system blow this air out.

Do RV furnaces run on electricity?

While onboard RV furnaces do not run solely on electricity, the heater that’s built into your RV’s HVAC system does — and there are a variety of electric heaters on the market you can add to your RV’s interior for extra heating.

Why is my furnace not kicking on?

The Pilot Light (Faulty Ignition Sensor) The pilot light or ignition sensor is usually the most common issue when your furnace will not ignite. … Put the front panel back on, turn on the gas, and then turn the furnace back on. Turn up the temperature on your thermostat to see if your furnace will now fire up.

What happens when furnace pilot light goes out?

If your pilot light repeatedly goes out, this is a likely culprit. If this flame sensor should fail, gas will continue to flow even after the pilot light has been extinguished, causing a safety hazard, and requiring immediate repair.

What does the pilot light look like?

You should be able to clearly see the flame of the pilot light. The first thing to check is the color of the flame. A natural gas flame should be a bright blue color with a small amount of yellow at the very tip. A propane flame will have more of a bluish-green flame with a tinge of yellow at the tip.

How do I reset my Dometic RV furnace?

Press the “+” button and, while holding it, also press and hold the On/Off Mode button for three seconds. LCD will show ― ― . Press the On/Off Mode button again to turn system off. This completes the initialization.

Why is my furnace in my camper blowing cold air?

Sail Switch This is a very common issue with RV furnaces not fully igniting, and as a result, just blowing cold air. … This switch can become blocked with pet fur, dust, and debris from the RV sitting, or from being collected and blown around by the fan itself.

How do I troubleshoot my RV thermostat?

Step 1 – Ensure You Have the Thermostat on the Correct Setting. …
Step 2 – Turn the Thermostat Down or Up 5-Degrees. …
Step 3 – Check and Replace the Thermostats Batteries. …
Step 4 – Air Blast the Thermostat. …
Step 5 – Test Connections and Wires.

Can Hear Your RV furnace click on but it does not fire up?

Most likely, your furnace is making a clicking noise and not providing heat because your furnace’s spark igniter is trying to ignite your pilot light or burners but is failing to do so. In other words, there’s an ignition system malfunction that needs to be fixed.

Can you clean a furnace ignitor?

Try Cleaning the Ignitor With Compressed Air If your furnace has a spark ignitor and it’s working haphazardly, it too could be covered with soot, and a blast of compressed air may be enough to clean it. Compressed air can also clean a blocked pilot tube that is causing the pilot flame to burn weakly or not at all.

How do I know if my furnace flame sensor is bad?

Switch off the power to your furnace.
Close the gas valve.
Take out the mounting screw.
Carefully pull out the sensor.
Inspect the sensor: if the insulation is intact but appears sooty, burnt or slightly corroded, it might only require cleaning.

Who makes Hydro Flame Furnace?

Atwood/Hydroflame Furnaces & Heaters.

How many BTU is a camper furnace?

The average RV furnace uses between 20,000 and 50,000 BTUs. However, the actual amount of propane an RV furnace uses depends on its size. The larger the unit, the higher the BTUs and the more propane used and heat produced. In general, one gallon of propane will fuel 92,000 BTUs.