How do I restart my furnace

First, turn off the power supply to the furnace by turning off the breaker in the circuit box.Locate the reset button on the furnace and press it to reset the furnace. … If the button is popped up, press it down.Return the cover to the blower compartment and turn the power on.

Should I hit the reset button on my furnace?

The purpose of the reset button on a furnace is to shut it down before it can trip your circuit breaker. The need for this may arise if the furnace becomes too hot, or if there is some sort of electrical system interruption. To get the furnace working again, you simply press the reset button back down again.

How do I get my furnace to kick on?

Check your circuit breakers.
Check your thermostat settings.
Ensure your furnace filters are clean.
Check your pilot light.
Check your blower motor.
Check the furnace ignition switch.

Can you reset a furnace?

Steps to Reset Your Furnace Most furnaces that are less than 30 years old can be easily reset by turning the furnace off and back on. … If you can’t find a switch at the furnace you can turn off the circuit breaker to the furnace at the main circuit breaker box. Wait about 10 seconds.

How long does it take for furnace to reset?

Either way, restarting a furnace is a relatively simple task that takes no longer than 10 minutes to complete. Follow these steps to reset your gas furnace: Turn the circuit breaker off and switch the furnace power button off too.

How do you reset a furnace blower motor?

Step 1: Turn off the power to the furnace. …
Step 2: Remove the blower compartment cover. …
Step 3: Make sure the blower is completely cooled off. …
Step 4: Locate the reset button. …
Step 5: Press the button in (assuming that this is your issue and that the button has popped).

Why is my furnace not kicking on?

The Pilot Light (Faulty Ignition Sensor) The pilot light or ignition sensor is usually the most common issue when your furnace will not ignite. … Put the front panel back on, turn on the gas, and then turn the furnace back on. Turn up the temperature on your thermostat to see if your furnace will now fire up.

How do I reset my furnace lockout?

Most modern gas furnaces can be reset by turning off the power, waiting around 20 seconds, then switching the power back on. Other furnace models may exit lockout after 1-2 hours and attempt to power on again. If your furnace has a pilot light, you may need to relight it following the manufacturer’s instructions.

How do you reset a furnace after overheating?

Turn down the thermostat to its lowest setting.
At the circuit breaker, turn off the power to the furnace.
If this is a gas furnace, turn off the gas supply at the valve for the main gas pipe, but leave the pilot’s gas supply on.
If the pilot light was out, light a match to relight it.

Why is my furnace blowing cold air?

Your furnace may be blowing cold air because the filter is too dirty. A dirty air filter blocks airflow over the furnace’s heat exchanger, causing it to overheat. When overheating, your furnace can trip a high limit switch, causing the furnace burners to shut off so that the heat exchanger does not crack.

Article first time published on

How much does it cost to relight a pilot light?

Most service providers will charge a standard fee per visit that typically covers the cost to relight a gas water heater. This service call price can range from $80 to $100.

Why is my furnace reset button not working?

Obstructed airflow: Sometimes the reset button gets tripped because the furnace isn’t receiving enough airflow. … Dirty flame sensor rod: Every now and then, the flame sensor rod gets dirty and shuts the furnace off. Make sure you wipe it off regularly. Low fuel: Low fuel is also a common cause of burner failure.

Where is the reset button on a blower motor?

Examine the exposed components in the furnace cabinet to locate the blower motor; look for a small silver box positioned toward the top of the cabinet. Mounted just above this box you should see a small round component with a raised red or white button at the center; this is the blower reset switch.

What happens if a furnace overheats?

The most serious risk of an overheating furnace is stress cracks in the heat exchanger caused by overheating. The vast majority of premature heat exchanger damage is due to overheating as the heat stress causes cracks near the welds and bends.

Should my furnace light be blinking?

When your furnace light flashes, that’s just another way it’s trying to communicate with you that there is a problem. When you see a flashing light, your furnace is sending you an error code. … Check your circuit breaker box to see if you tripped the breaker for the furnace.

How can the safety lockout be reset?

How can the safety lockout be reset? Setting the thermostat below room temperature. When is the igniter energized on an induced draft furnace that uses hot surface ignition? After the draft switch closes to prove the draft.

Why is my furnace blowing out lukewarm air?

The lukewarm air coming out of your furnace can also be the result of leaky air ducts. If your ducts are leaking (and ENERGY STAR says that almost all homes leak about 30% of the air in their ducts), cold outside air is making its way into your ductwork. This can cause the air to feel only lukewarm.

Can I relight the pilot light by myself?

If your pilot light goes out, your furnace will not be able to produce heat because its burners will not ignite. Often, homeowners can relight the pilot themselves.

Is it bad if the pilot light goes out?

A pilot light is a small flame that is built into your gas heating appliances, such as a furnace or water heater. … If the pilot light goes out for any reason, the current stops, the valve closes, thus preventing any gas from leaking.