Press and hold the left and right arrow buttons at the same time for at least 3 seconds. Until you see the word “CLEARED” on the screen. Your ESP-Me is now restored to the factory default settings.
How do you reprogram a Rainbird?
- Check the time and date on the controller to make sure it is accurate. …
- Rotate the dial to the “Watering start time” position and press the “+” or “-” keys to reprogram the time of day the watering cycle begins.
How do I reset my irrigation system?
- Turn the control dial to the “off” position.
- Press the “next” button to access the clear-memory feature. …
- Press and hold the “off” button until the display stops blinking.
- Turn the control dial to the “run” position.
- Press and hold down the “minus” arrow and “prog” buttons simultaneously.
Why is my Rainbird not working?
Circuit breaker/fuse – Check the condition of the circuit breaker or fuse, if it has been blown the most likely reason is a field wiring short. An Electromechanical controller will stop on the station that caused the problem. Reset the controller to its rest position and replace the fuse or reset the circuit breaker.How do I reset my sprinkler controller?
- Unplug the controller’s transformer.
- Press and hold down the, and buttons.
- Plug the controller’s transformer back in.
- Release the , and buttons. The display should now show 12:00am. All the memory has been cleared and the controller may now be reprogrammed.
Why are my sprinklers not popping up?
— A broken sprinkler head is one of the most common reasons that your pop-up sprinkler heads do not work properly, even when the water is turned on at a full blast. Broken sprinkler heads are easy to identify. Simply look for cracked casings, broken plastic pieces, or heads that refuse to pop-up out of the ground.
How do I delete start time on Rainbird?
Please call 800-RAINBIRD or call your local professional irrigation contractor for assistance. Turn the dial to “Set Watering Start Times”. You will see the 1st start time for Program A. Press the right or the left arrows to toggle between start times and find one of the other start times to turn off.
Why is my sprinkler system not turning off?
It is possible that the sprinkler valves need a good cleaning since dirt and debris can get trapped in the valve and cause problems. So, for a little DIY practice, check to see if the valves are clogged. If the valves are clean, check to see if they are cracked or broken.Why is my controller not starting the watering cycle?
Go to one of the irrigation valves and turn the solenoid 1/4 to 1/2 a turn counter-clockwise. … If the valve opens and sprinklers turn on, your valve is working and you’ll need to check the controller and field wiring. If the valve did not turn on any of the sprinklers, the water to the valves is still off.
How do I know if my sprinkler controller is bad?- Controller Isn’t Working Properly.
- Low or High Water Pressure.
- Sprinkler is Stuck or Won’t Come Up.
- Puddles on Lawn or Around Sprinkler.
- Uneven Spray Patterns.
- When to Call a Professional.
How do I reset my core controller Hunter?
- Turn the dial to the advanced features position. Press the down arrow to scroll to page two. Select ERASE ALL by pressing the “+” button.
- Press and hold the “+” button. The display will briefly inform you to please wait and then indicate when the reset is done. 2.666665.
How do you clear the alarm on Rainbird ESP?
The status light on the module of the shorted station will blink continuously. Remove the shorted station wire from the module. In the Auto dial position select Alarm and Clear.
How do I program my Rainbird ISA 304?
Set the correct time and day by turning the programming dial to “Time & Day”; the hour and minutes display will flash. Press the “Advance” button (the right arrow key) until the day is flashing. Press the up or down arrow keys until the correct day appears. Press the “Advance” button again and the hour will flash.
How do I delete a program from Rainbird ESP tm2?
You can delete a program if you have the Rain Bird app on your smart phone. Good advice. You can also set the dial to ” seasonal adjust “ . Then press both arrows simultaneously for at least three seconds, until ” clear” or ” cleared” appears.
How do I turn off second watering time on Rainbird?
To turn a watering start time to OFF, use the + button to advance the start time past 11:30PM, instead of displaying 12:00AM, it will display OFF.
How do I turn off Rainbird sprinklers?
To turn off your sprinkler system at the controller, simply turn the dial/knob on the controller to the off position. Most controller user manuals can be found online, such as Rain Bird controllers ().
How do I know if my Rainbird solenoid is bad?
- The Water Won’t Shut Off. If you have this problem, it’s very likely the solenoid. …
- Low or Uneven Water Pressure. The solenoid controls the water pressure. …
- Water Leaks. There are many points in a sprinkler system that can leak. …
- Current Testing. …
- Valve Inspection. …
- Parts Replacement.
What does no AC mean on my Rain Bird sprinkler System?
The “No AC” means the battery is powering the unit but won’t power the sprinkler controls. It’s either the prime power source or the unit.
How do you flush a Rainbird valve?
To flush valve to clear debris: Turn the bleed screw counter-clockwise ONLY 1 turn. Flush one minute and turn clockwise to close. Test and flush each line before sprinklers are attached. Several models of Rain Bird 24 Volt valves are available for home use.
How do I increase the water pressure in my pop up sprinklers?
Remove a few sprinkler heads from each of the zones in your system and cap the plumbing that led to them. Decreasing the number of sprinkler heads will increase the water pressure in those that remain. Install a boost pump on the main irrigation line.
How do I find a sprinkler head that does not pop up?
Use a metal detector to find buried sprinkler heads. Many valves have metal parts you can locate by running the metal detector over the surface of the ground. Valves are located directly under sprinkler heads. Look for large, dry, brown spots in your lawn.
How do you fix a stuck Rainbird sprinkler head?
- Disassemble the sprinkler head. …
- Take off the filter at the bottom of the head. …
- Rinse the filter in a bucket filled with clean water to wash out debris.
- If this doesn’t work you’ll need to have the sprinkler head replaced. …
- If it does work, make sure the head is properly adjusted when you re-install it.
Why won't my sprinklers turn on manually?
If your sprinkler system won’t turn on or if you have low water pressure, this could be caused by the valves not being turned on all the way. Just locate the valves and make sure they are both turned on (you should have 2 valves, one located on the horizontal pipes and one for the vertical ones).
