How do you use a tree pruner

Some pole pruners have a saw blade on the cutting head. Use this type to saw partially through a branch, and then pull the string to finish the cut. Most pole pruners will cut branches up to 2 inches in diameter.

How does a pole tree pruner work?

Some pole pruners have a saw blade on the cutting head. Use this type to saw partially through a branch, and then pull the string to finish the cut. Most pole pruners will cut branches up to 2 inches in diameter.

What is the rope for on a tree pruner?

The pulleys add to a two-to-one advantage provided by the lever in a lopper to compensate for the effort it takes to heft the pole up in the air to prune a tree branch. Restring your pruner as its rope begins to show wear to maintain a safe, efficient tool.

What is the best tool for cutting tree branches?

A chainsaw provides the cleanest cut when you’re dealing with limbs thicker than 3 inches. If your pruning job requires a chainsaw, it’s recommended that you contact a certified arborist. A pole pruner allows you to cut branches that are beyond your reach. Most pole pruners cut limbs up to 2 inches in diameter.

Are pole pruners easy?

Though easier and safer to use than its cousin the pole saw (since pruners can only cut much smaller wood), pole pruners must still be used cautiously. You are cutting smaller wood, but the wood bounces or sails around and falls less vertically than heavy wood.

How do you put the blade on a Fiskars Tree Pruner?

Attaching the blade is as simple as removing the included wing nut, inserting the blade into the slot, and tightening the wing nut. That’s it. You’re ready to go to work!

What is the best telescopic tree pruner?

GARDENA Telescopic StarCut 410 Plus – BEST PICK.
Draper Expert Telescopic Tree Pruner – RUNNER-UP.
Stihl HT133 Long Reach Pole Pruner – PROFESSIONALS’ PICK.
Silverline 245077 Extendable Pruning Saw 1.5-2.5 m.
Wolf Garten Tree Pruner.

Can I cut an overhanging branch?

Can I cut off overhanging branches? Yes, provided it is done without trespassing onto the other person’s property. It is also permissible to climb into the tree to undertake the work, again so long as it does not require going into the neighbour’s garden/land.

Can you cut back a Neighbour's overhanging tree?

If a tree’s branches overhang into your property from a neighbour’s, you can trim them, but only up to the property line. You can’t lean into the neighbour’s garden to do this, though, as it constitutes trespass. If a tree is covered by a Tree Preservation Order, you can’t cut the branches.

How thick can a pruning saw cut?

Pruning saws are your choice for wood about 1.5 inches thick or more and your last resort before the very large stuff that you might only be able to do with a chainsaw. As such, they are used to cut a wide range on the large end of wood thicknesses.

Article first time published on

How do you use a hand saw on a tree?

Position the hand saw over the branch as close to the trunk as possible, and begin slicing back and forth, one-third of the way through. Use the entire length of the blade for each cut or stroke through the wood, and work slowly to prevent the blade from sticking or jumping.

How do you trim tree branches yourself?

Trim off any suckers growing at the base of the trunk.
Remove all the dead or dying branches.
Prune out unwanted or hazardous branches.
Remove any damaged or weak branches.
Trim out overlapping branches that rub together.

How do you trim small tree branches?

Start with dead and diseased stems.
Remove any crossing, rubbing or inward facing stems.
Reduce size by cutting one or two older stems to ground level.
Prune a few longer branches back to shorter adjoining branches.

What do you use to cut small branches?

Also called hand pruners, pruning shears are perfect for cutting small twigs, up to 1 inch in diameter. To touch up small, live branches, look for bypass pruning shears. The tool resembles a pair of scissors and is good for trimming twigs at awkward angles.

How do I attach rope to pole pruner?

No-Pulley Pruner Thread the end of the rope up through the rope guide on the pole below the pruning assembly. Pull the end of the rope up to the hole in the end of the lever on the pruning blade. Thread the rope through the hole. Tie a knot to prevent the rope from coming loose.

How do you thread the rope on a Fiskars Tree Pruner?

Remove the old rope, taking particular note of how it loops over the two pulleys. …
Thread one end of the rope through the top pulley from the outside in toward the cutting blade assembly.
Pull the rope through and into the slide around the bottom pulley.

What is a pole pruner?

Definition of pole pruner : a tool for pruning with the cutting parts on the end of a rod or pole 6 to 12 feet long.

Are pole saws worth it?

While pole saws can make pruning a whole lot easier, they’re not right for every situation. That is, if you only need to prune thin twigs, vines, or foliage, you may not need a pole saw. However, if you aim to cut tree branches between 2 and 8 inches in diameter, a pole saw could be just the ticket.

How big of a branch can you cut with a pole saw?

In terms of cutting ability, this type of pole saw will work best on tree branches between three and eight inches in diameter.

Is it safe to use a pole saw on a ladder?

Pole saws are kind of wildly, much harder to control than a chainsaw, they can tire your arms out very quickly, make you lose your balance, you should never use a pole saw on a ladder.

How do you top a tree with a pole saw?

The correct position for using a pole saw is to stand off to the side of the branch, not directly below it. This position will reduce your chances of injury when the wood falls out of the tree. Make sure you can hold the end of your pole saw at chest level too. You want the pole saw to be at an angle while you cut.

How do you put the blade on a pole saw?

Disassemble the old blade by removing the bolts that hold it onto the pole shank or head of the trimmer. …
Wrap the old blade in newspaper and discard or recycle. …
Unwrap the new blade and slide it into the slot that held the old blade.
Reattach the bolt or bolts through the shank and tighten firmly.

What should I look for in a tree pruner?

Features to Look for in a Tree Pruner You need a tree pruner that is able to reach most if not all of your tree’s branches. For moderately-sized trees, a fully-extended length of 12-14 feet is recommended. For smaller trees, hedges and shrubs, it’s recommended that you get a tree pruner that extends 6-10 feet.

How well do pole saws work?

Manual pole saws work very simply. Using a push-pull motion, the blade cuts the wood on the pulling stroke. Simple, right? Simple, effective and often better for your tree.