How does a primer bulb work

ANSWER: The primer bulb, which is located in the fuel line between the gas tank and the engine, is used to fill the carburetor with fuel when the engine is started cold. … Always hold the end nearest the engine up. This allows the internal valves to open and close properly. Also, do not squeeze the bulb excessively hard.

How many fuel lines does a chainsaw have?

Most chainsaws have two fuel lines — one that feeds fuel into the carburetor and a return tube that allows unused fuel to flow back into the chainsaw gas tank. The return tube may be slightly larger in diameter than the tubing that feeds the fuel, or both tubes may be the same size.

How do you adjust a craftsman carburetor?

Locate the carburetor on your Craftsman equipment. …
Turn the main mixture and idle mixture screws on the carburetor counterclockwise about one full turn with a flat-head screwdriver. …
Start the engine with the transmission in neutral and let it run for several minutes.

How do you replace fuel lines on a Poulan chainsaw?

Let’s get started. …
Remove the top cover.
Remove the air filter housing.
Remove the carburetor.
Remove the fuel return line.
Cut the new fuel line to the proper length.
INSTALLING THE NEW FUEL RETURN LINE [top] 7. …
REASSEMBLING THE UNIT [top] 8.

How do you adjust the carburetor on a Craftsman 42cc chainsaw?

With the engine running turn the high speed needle clockwise until the engine runs rough. Turn the needle counter clockwise slowly until the engine runs smooth. Make this adjustment with both screws and the engine should run smoothly and at the highest fuel efficiency.

Can I run my chainsaw without a fuel filter?

Well as long as the lack of that fuel filter doesn’t cause leaking at the inlet connection, then yes it will run fine …. but only for as long as whatever the filter might have caught and preventing it from clogging jets and passages.

How do I change my fuel filter?

Relieve the pressure in the fuel line before disconnecting it. …
Look at the old filter and the new one before disconnecting anything. …
Remove whatever is holding the old filter in place and remove it.
Put the new filter on in the same position as the old filter.

Are all primer bulbs the same size?

all primer bulbs are not the same size! quit telling everybody it will fit just because it fit yours… Shoppers find videos more helpful than text alone.

Which line goes where on a primer bulb?

The (clear) fuel intake line runs from the top of the carburetor (straight nipple) and goes to the short post on the back of the primer bulb. The return line (blue) comes from the long post on the back of the primer bulb and goes into the bottom of the fuel tank.

Should the primer bulb stay full?

the primer bulb should be mostly fuel, check the lines they get old and start cracking. replace with tygon. there is a fuel pump in the carb operated by pulses from the crank case, the diaphragm in it can can go bad also.

Article first time published on

Why is my primer bulb sticking?

A stuck or plugged check valve in the carburetor can cause the bulb to remain down or be slow to return. A plugged fuel filter can do the same. Remove the filter and repeat the test. Check valves are non-serviceable and replacement of the valve body is the only fix.

Why do you need a primer bulb?

A primer bulb is important because it is helps to fill the carburetor with the correct amount of fuel. It does this by pulling fuel through the fuel line. You may need to fix or replace your primer bulb if: It is not creating proper suction.

What size fuel line does a Poulan chainsaw use?

Fuel Line Specifications. This is the replacement fuel line 25 Inch for several OPE products that use small engines. The fuel line carries fuel from the tank to the carburetor.

Why is my chainsaw not getting gas?

If your chain saw isn’t getting gas, the trouble most likely lies in one of those three core components: the fuel tank, the spark plug or the carburetor, or one of the minor parts adjacent to the three.

Why does my chainsaw leak gas?

Gas Chainsaw: What should I do if my chainsaw leaks gas? … If fuel leaks from the carburetor, rebuild or replace the carburetor to prevent gas from leaking. Replace the fuel tank cap if its seal is damaged and leaking. Check the fuel tank and replace the tank if it’s damaged.