The F01 indicates a failed electronic machine control board. This error code can sometimes be caused by a glitch or power surge through the electrical lines. You may be able to clear this code by unplugging the washer for 5 minutes.
How do I fix F01 error?
The F01 error is an internal failure of the main control board. The only thing you can do is try and reset the electronics by killing power to it at the breaker/fuse panel on your home for one full minute then restore power. If after that the problem persists the control board will need to be replaced unfortunatley.
How do I fix my Whirlpool F01?
The Whirlpool Duet Dryer F01 error may be able to be fixed with a simple reset of the main control. Unplug the dryer for 1 minute and plug it back in this will reset the control if the error persists after that you will need to check the dryer thermal fuse.
What causes F01 error?
If your Whirlpool dryer is displaying an F01 error code, this means there is something wrong with the control board or one of the components connected to it. It is commonly caused by a power failure or after a power surge occurs.How do I clear the error code on my Kenmore dryer?
Unplug or turn the circuit breaker off for 30 seconds. Plug the power cord into the wall outlet or turn the breaker back on and wait 30 seconds. Press the Pause / Cancel / Stop button twice to clear the display.
How do I clear the error code on my Kenmore washer?
- Look for the “Pause/Cancel” button on the washer control panel. …
- Press the “Pause/Cancel” button twice to cancel the wash cycle. …
- Connect the water supply hoses back to the washer and turn on the water spigots.
How do you test a dryer control board?
- Unplug your dryer and remove the control console panel on the top of your dryer to locate the rotary switch.
- Set your multi-meter to the Rx1 setting and place the probes on the switch’s terminals. …
- With the probes still touching the terminals, press in on and hold the switch.
What does F01 mean on a washing machine?
F01 — Electronic circuit board fault. Issue: Washing Machines is not operating – some or all functions are not selectable. Advice: We recommend you disconnect (unplug) the appliance from the mains supply for a minimum of 2 minutes. Reconnect supply and wait 30 seconds and try starting the machine again.How do I reset my Duet dryer?
If your Whirlpool dryer displays a “PF” error code, indicating a recent power failure, the dryer will need to be reset and restarted. This is done by pressing “Start” for a few seconds to restart the dryer. If the dryer does not restart automatically, select a new cycle and any options then press “Start” to begin.
How do you unlock the door on a Whirlpool Duet dryer?Press and hold the “Control Lock” button for at least three seconds to unlock the control panel. Once unlocked, you have full access to the dryer controls.
Article first time published onHow do I clear the error code on my Whirlpool washer?
To remove the code, press pause or cancel button twice and the power button once. If the code is still displayed, unplug the washer or disconnect the power for one minute. Items were detected in the washer during the Clean Washer cycle. Remove items from the drum and restart the Clean Washer cycle.
What does F1 on a Whirlpool dryer mean?
Whirlpool dryer also displays f1 error code if the wires going to the central module have an opening or unstable contact.
Where is the thermal fuse on a Whirlpool Duet dryer?
Remove the back access panel on the dryer, and look for the exhaust duct near the bottom of the unit. The thermal fuse is either circular or oblong, often white plastic with black material in the center and two wire leads. The thermal fuse is mounted on the exhaust duct.
How do I fix my F01 on my Kenmore dryer?
This error code can sometimes be caused by a glitch or power surge through the electrical lines. You may be able to clear this code by unplugging the washer for 5 minutes. If the code returns after plugging the washer back in, then the electronic machine control board will need to be replaced.
How do I fix Hotpoint F01?
When your washer dryer shows error message F01, we advise you to disconnect and unplug your Hotpoint washer dryer from the mains supply for 3 minutes. After 3 minutes have passed, reconnect your Hotpoint washer dryer and wait 30 seconds before you start up the machine again.
How do I fix the F01 code on my Maytag dryer?
Power unit down by turning off the circuit breaker(s) for one (1) minute. Power unit up by turning on the circuit breaker(s). Start a time dry cycle. Monitor the dryer for one (1) minute to ensure the error code does not display again.
How do you know if your dryer is dying?
- Drum won’t turn. If the dryer drum isn’t turning, but the dryer itself engages when turned on, you probably have a belt issue. …
- Heat feels weak or insufficient. …
- Dryer refuses to start. …
- Banging or popping noises. …
- Squealing or grinding. …
- Dryer stops mid-cycle.
What happens when a thermal fuse blown on dryer?
A thermal fuse will blow when the temperature gets too high, not when it’s drawing too much current. … When it blows, the dryer stops generating heat. It’s necessary to replace it before the dryer will run again.
Will dryer start if thermal fuse is blown?
Will the dryer run if the thermal fuse is blown? Unlike a thermostat that can reset itself, once a dryer thermal fuse blows, it will need to be replaced with a new one before the dryer will run.
What does Le mean on my Kenmore washer?
The LE error code on a Kenmore front-load washer means that the washer won’t run at all or at the expected speed because the drive motor has locked up. … Try these troubleshooting steps with your washer to find the cause of the drive motor problem and clear the LE code.
What does the code ie mean on a Kenmore washer?
The IE code indicates that the washer detects a problem with water fill. Make sure that the hot and cold water supply faucets behind the washer are fully open. … You can shut off the water supply faucets and check the inlet water screens on the back of the washer for debris or deposits.
Why is my Kenmore washing machine not draining?
If the washer won’t drain water the drain pump might be defective. It’s also common for a small sock or other article of clothing to get caught in the drain pump or in the drain hose. Check both for an obstruction before replacing the pump. If the washer won’t drain there might be a clogged pump or hose.
Where is the dryer reset button?
Many dryers are equipped with a reset button on the control panel.
What would cause a whirlpool dryer not to heat?
When gas or electric Whirlpool Dryer is not heating up, it usually caused by: Burnt Heating Element or Gas Valve Solenoid, Burnt Thermal Cut-Off Fuse, Defective Cycling Thermostat Or Gas Ignitor, Malfunctioned Flame Sensor.
How do I fix error code F01 Indesit washing machine?
- Turn off the washing machine and unplug the connector.
- Wait 2 minutes and put the connector back in.
- Wait 30 seconds and turn the washing machine back on.
What does UC mean in Samsung washing machine?
Error CodeCauseUCExcessuve Fluctuation In The Supply Voltage (voltage has fluctuated outside 176-286vAC)UE, E4Unbalanced Error (the washing load in the drum is unbalanced i.e. clothes may have got trapped inside a large towel and resting on one side of the drum)
What does E01 and F01 mean on a Whirlpool washer?
In Whirlpool washer error code E01 F01 is usually associated with the central control unit. And sometimes, it is associated with a transistor responsible for storing re-recordable memory. It means that if there is no information about the selected mode on it, then there will be no reaction to the commands.
How do you manually unlock a Whirlpool Duet washer?
You can manually unlock the washer by removing the top (remove screws on the back of the top panel and slide the top panel back to lift off. then with the washer unplugged reach down and pull a small ring on the top of the door lock to manually open the door lock.
How do I unlock my Whirlpool dryer?
Press and hold the Control Lock Key for 3 seconds to unlock the machine. You will notice the machine count down from 3-2-1. The control lock may be a stand alone key, or it could be a dual function key paired with another button like Extra Rinse, Steam, etc.
How do I unlock my dryer?
To lock and unlock the dryer controls: Press and hold the Extended Tumble and – (minus) buttons for 3 seconds. The control lock icon will flash while locking/unlocking, stay on when locked, and turn off when unlocked. NOTE: The Power button can still be used when the machine is locked.
Can you reset a Whirlpool Cabrio washing machine?
How To Reset Whirlpool Cabrio Washer: Turn the washer off. … Turn the washer off and unplug it for 10 seconds. Finally, turn on the washer and it should now be reset.
