Sleep Mode heats the spa to within 20°F/10°C of the set temperature only during filter cycles. “SL” will display solid when temperature is not current, and will alternate with temperature when temperature is current.
How do I change Viking spa mode?
The mode is changed by pressing the “Temp” button, then pressing the “Light” button. Standard Mode is programmed to maintain the desired temperature. Note that the last measured spa temperature displayed is current only when the pump has been running for at least 2 minutes.
What does SL mean on a strong spa?
SLEEP – SL, SLP Sleep is considered a vacation heater setting, and will maintain your spa water at the most affordable price. Spa will only heat during your filter period. The water temperature may drop up to 20 degrees below your desired temperature.
What mode should my Viking Spa be in?
We recommend the standard mode as the normal mode of operation. 12.Why does my hot tub says SL?
If the SLP or SL Message is ON Solid (Not Flashing) on the Display, the Spa is Operating in the Sleep Heating Mode, but there is No current water temperature because the Spa is between Filter Cycles. … The Heater will only operate and Heat up to Set Temperature during the Filter Cycles.
What does F4 mean on a Viking Spa?
CODEERROR CODE DESCRIPTIONF48 hours daily filtration; system message, not an errorF612 hours daily filtration; system message, not an errorFFahrenheit, used to indicate panel is in Fahrenheit mode; system message, not an errorFB-ERFiber optic error; accent lighting
What is SL on a hot tub?
SL: Sleep – Sleep mode will only allow the spa to heat within 20 degrees of the set temperature.
How do you fix the error code on a hot tub?
This error message is similar to the FLO error message. Like FLO issues, this can commonly be fixed by topping off your hot tub water level. DR or DRY will show up if there is little to no water travelling through your heater.What does PR mean on a Viking Spa?
Pr = When spa is first actuated, it will go into Priming Mode. ILOC = Interlock failure – possible pump or ozone spike . (—) =Unknown water temperature.
How are Viking hot tubs rated?Viking Spas and hot tubs are generally considered to be a solid, mid-range hot tub. They have good build quality and the standard range of features, generally at a reasonable price point. While they don’t do too much out of the ordinary, they do use a proprietary filter system.
Article first time published onHow do you prime a Viking Spa?
When your spa is first activated, it will go into Priming mode, indicat- ed by “Pr”. The priming mode will last for less than 5 minutes. Then, the spa will begin to heat and maintain the water temperature in the Standard mode indicated by “St”. The start-up temperature is set at 100°F/37°C.
Why does my hot tub pump run all the time?
If your spa’s heating element is burnt out, the pump may run all the time. Try turning the thermostat to OFF or LOW to see if the pump turns off. There’s a possibility if it doesn’t stop running that the timer is faulty or something is wrong with the circuit board.
How do you reset a strong spa hot tub?
Reset the GFCI breaker by switching the breaker to the full OFF position, wait a moment, then turn the breaker back on. The spa should have power again.
Why won't my Viking spa heat up?
If your spa heater won’t heat, remove and clean the filter(s) to rule out a pressure or flow rate problem in your hot tub heater. Low water level, a clogged pump impeller, closed valves, clogged pipes, or blocked spa drain covers can also cause flow issues.
What does Dr mean on hot tub?
Newer hot tubs have a digital display for error codes that can assist with troubleshooting. A message such as “dr” or “dry” or “heater dry” is a warning that there’s no water in the heater tube, says Niagara Hot Tubs. … If the water is low, add water to the proper level and try restarting the pump and heater.
How do you winterize a Viking Spa?
- Turn Off The GFCI Circuit Breaker. …
- Remove Your Hot Tub’s Side Panel. …
- Attach A Garden Hose To The Drain Hose. …
- Loosen Unions On The Heater And Pumps. …
- Remove The Drain Plug From The Pumps. …
- Use A Wet-Vac To Remove Water From The Lines. …
- Replace Drain Plug On Pumps. …
- Add Hot Tub Antifreeze.
How do you drain a Lazy Boy hot tub?
Attach the hose adapter to the lower water pipe on the outside of the spa. Then, attach your hose to it, with the other end in a drain-off area as the water’s chemicals can harm grass, plants and flowers. Remove the lower stop cap from inside the spa and allow the water to flow out.
How do you remove Viking spa jets?
Removing and Replacing Spa Jet Inserts. Most adjustable jets have an outer ring around them that allows the water flow to be turned down or off. To remove an adjustable jet, rotate the ring counterclockwise until it stops, then keep turning to unscrew the insert from the jet housing or body.
What does F8 mean on a hot tub?
Filtration Cycles run from F1 to F8 (F1 = 1 hour every 12 hours / F8 = 8 hours every 12 hours). Preset cycle set from factory is F1, so if in ec or sl mode your water will not reach desired temperature.
What does F2 mean on my hot tub?
The F2 error code is usually from a balboa power pack system and normally is referring to a flow issue in your hot tub. … A dirty filter can often be the culprit here so make sure to either replace or give your hot tub filter a good cleaning. Look at your intakes and out takes and make sure they are clear of debris.
What is the most reliable hot tub brand?
- Sundance Spas. Known for: Sundance Spas has a time-honored history and offers five series of spas, providing an option for any budget. …
- Master Spas. …
- Jacuzzi. …
- Bullfrog Spas. …
- Hot Spring. …
- PDC Spas. …
- Marquis Spas. …
- Cal Spas.
Are Nordic spas good?
For over 25 years, Nordic Hot Tubs has led the industry in providing high quality, therapeutic, and affordable hot tubs. At the heart of our mission is Nordic’s STAR philosophy meaning every hot tub should be Simple, Therapeutic, Affordable, and Reliable.
Is Viking A good spa?
Viking makes a nice no frills hot tub that is reliable.
What does it mean to prime a hot tub?
Hut tubs need to be primed in order to purge air. Air restricts the pump action. You can tell when a hot tub isn’t primed properly because the motor operates, but no water flows to the jets. Purge the air in your hot tub pump. … You can prime your hot tub by purging the air yourself.
What is priming mode on a hot tub?
The purpose of the priming mode is to manually activate each spa pump prior to the automatic heat cycle being started. Typically, cycling each pump a few times will prime or purge any air from the plumbing. … That’s it, your hot tub is now full and ready for the next steps.
How many gallons Viking Spa?
Seating Capacity4-5 AdultsAverage Spa Volume290 GallonsDry Weight495 lbs.Total Filled Weight2,900 lbs.Cluster Storm Jets8
Should Jets be on when heating hot tub?
Before covering your hot tub, make sure to turn on the jets as this will accelerate the pace of your hot tub’s heating. By running the jets, you’re allowing the heated water to be circulated and evenly distributed to all areas of the hot tub.
What temperature should I keep my hot tub when not in use?
We always recommend keeping the temperature at 38°C, not only will this keep you warm, it also helps to protect your hot tub as the heat generated stops your power pack from freezing over. Make sure to always keep the cover on when you’re not using it, so the heat doesn’t escape.
How long should a spa pump run per day?
Since your hot tub pump circulates the warm water as well as the sanitizer, a general rule is to follow manufacturer recommendations or leave the pump on for a minimum of eight hours per day.
What does PR mean on a strong spa?
PRIMING THE PUMP Turn the spa on and wait for PR (Priming Mode) to appear on the topside display. Press the JETS1 button to turn on the pump, then let it run for 10 seconds. The pump should be running on low speed.
