What is a plunge saw used for

Unlike other saws, a plunge saw can be fed at the start of the material or be plunged directly into where you need to cut. This is handy for cutting the likes of worktops for sinks and hobs. A plunge saw is like a circular saw with a blade that spins and cuts, only with much more sophistication and accuracy.

What's the difference between a track saw and a circular saw?

A circular saw performs double cuts as the rip cuts and the crosscut, whereas the track saw three. The circular saw has a protective guard, whereas the track saw has none. A track saw has an enclosed blade to enhance dust extraction, whereas the circular saw lacks this feature.

Is a plunge saw worth it?

And when the quality of the finish of the cut matters, a plunge saw will always provide the highest quality of cut possible with no splintering, something hard to achieve with a circular saw. Using a plunge saw on guide rails ensures clean, accurate cuts. Plunge saws will provide much more accuracy than circular saws.

How deep can a plunge saw cut?

This plunge saw has a 12-amp motor, can make bevel cuts from -1 to 48 degrees (with positive stops at 0, 22.5, and 45 degrees), and has a depth of cut as much as 2 3/16 inches.

Which plunge saw is best?

Bosch GKT 55 GCE – BEST CHOICE PLUNGE CUT SAW 2021.
Festool TS 55 EBQ.
Makita SP6000. 4.0.
Metabo KSE55 Vario Plus.

Are plunge saw blades different to circular saw blades?

A plunge saw has a different design which removes the need for a conventional retractable blade guard, as the blade is enclosed within the machine. … This ensures multiple benefits versus the traditional circular saw including: The blade can be plunged at any point into the material you are cutting.

Can I use my circular saw as a track saw?

A circular saw can be used for all the same functions as a track saw, but doesn’t necessarily do them quite as well. If you’re on a budget, you can turn your circular saw into a makeshift track saw with straight edge guide.

What is the best cordless plunge saw?

Makita5.31DEWALT10.02Festool10.93Mafell15.24Bosch17.95

Can you use a track saw without a track?

All of the saws can be used without a track, just like a regular circ saw. But guiding them with a track guarantees dead-straight cuts. All the tracks work similarly: The saw straddles a raised rib that maintains a straight cutting line, and rubber grip strips on the bottom prevent the track from scooting during a cut.

Does Bosch make a track saw?

The Bosch GKT13-225 Track Saw with Plunge Action delivers precision and power, ideal for making table-saw quality cuts to wood and wood-based sheet goods such as laminated particle boards and plywood. The track-guidance system provides exact adjustments for precision end-to-end cuts and plunge cuts.

Article first time published on

Why is Festool so good?

So what makes Festool so good? We believe it’s because Festool has focused on creating high-performing tools that are robust, reliable and precise. Their numerous innovations, like their dust extractors and cordless options, put Festool in a league of their own.

How do you shave the bottom of a door without removing it?

To sand the bottom of a door without removing it, put the sandpaper on the floor, grit side up, and pull the door back and forth across it. Planing is usually the last resort, since it will mean touching up the planed area with a sealer or finish to match the door. A rasp-type plane will often do the best job.

How much should I cut off the bottom of a door for carpet?

Typically you only need to trim 1/2 inch from the bottom of the door. If that’s not enough, you can trim off up to 3/4 inch. Hollow-core doors, which are the most common for interior usage, are built around a frame on the outside perimeter. If you cut too much off the frame, the door will can separate.

How do you fly a door without splitting it?

Place painter’s tape on both sides of the area where you want to plane. This will keep the door from splintering and prevent the planer from scraping the paint. Painter’s tape is a good choice as it won’t peel off the paint as other types of tapes would.

What is plunge cut?

A plunge-cut track saw combines the maneuverability of a circular saw with the precision and stability of a table saw, allowing you to make clean, super-straight cuts on a single pass.

Are all plunge saw tracks compatible?

Not all plunge saws are supplied with tracks, or even designed to be used with them (e.g smaller machines like the Draper MPS600SF Mini Plunge Saw).

Do track saws need clamps?

Track saws make long, precise cuts faster and better than table saws and circular saws. They are light and portable, don’t need clamps and set up quickly and accurately.

What is Makita 40V?

Makita have launched the 40V max XGT™, a new standalone cordless system in 2020. 40V Max XGT is engineered for select higher-demand applications and although the 40V max XGT batteries look similar in size to 18V LXT batteries, XGT is a completely new system with its own tools, equipment, batteries, and chargers.

What is a track saw UK?

The plunge saw, also frequently known as the track saw, is one of the lesser-known power tools. The plunge saw is similar to and often confused with the closely-related circular saw due to its physical similarity and overlapping use.

Does Bosch make a cordless track saw?

The Bosch GKT18V-20GCL Track Saw with Plunge Action is a compact, one-battery cordless track saw with the performance of a corded track saw. … The saw’s track-guidance system provides exact adjustments for precision end-to-end cuts and plunge cuts. The cuts are table-saw quality, with virtually no splinters.

Is festool made in China?

Festool designs and engineers its portfolio of innovative power tool products in its home country of Germany and all Festool power tools are manufactured in Europe.

Why is festool so expensive?

Festools’ cost is largely in part to where it sources its products. unlike most major power tool brands Festool doesn’t leverage cheap labor in Asia. Rather, Festool uses manufacturing in Europe and North America. This makes the end products more expensive, yes, but also makes the quality that much better.